EMOTIVA XPA-7 Gen3 7 Channel Audiophile Home Theater Power Amplifier

The power amplifier performs the simple but critical job of boosting

the output signals from each channel of your stereo preamp or surround

sound processor to the level necessary to drive your loudspeakers. While

this may seem trivial, a really good power amp is essential to having a

great audio system, because any flaws in the performance of your power

amp are going to limit the performance of your entire system. Every

amplifier in the new Third Generation XPA series was carefully designed

to deliver superb technical performance, unsurpassed sound quality, and

an exceptionally accurate and dynamic rendition of all types of music,

thus ensuring that your entire system will sound its absolute best. Each

individual XPA amplifier is modular, and can be customized to provide

exactly the power and number of channels you need today, and expanded

later if your needs change; and multiple matching chassis enable you to

add even more channels, or more power, for a near endless variety of

options.

XPA-7

The new XPA-7 is a seven-channel audiophile quality power amplifier, and is perfect for powering:

All 7 main channels in a superb 7.1 channel home theater system

A high-end 5.1 channel system with bi-amped front speakers

The 7 main channels in an Atmos or DTS-X system with height speakers    




Configuration:

7 x High-Powered Single-Channel Modules (all slots populated)




Power output:

200 watts/channel RMS into 8 Ohms; all channels driven

Circuit Topology

The XPA-7 Gen3 is a fully modular audio

power amplifier with a high-efficiency switch mode power supply (SMPS),

independent, fully discrete, dual differential, high current, short

signal path Class A/B amplifier modules, Optimized Class H™ power supply

topology, and microprocessor-controlled fault protection.

The XPA-7 is powered by a high efficiency, audiophile grade, Switch Mode Power Supply (SMPS).

Audio Specifications

The XPA-7 Gen3 features seven of our High-Powered Single Channel Modules.  

Audio Specifications (Seven High-Powered Single Channel Modules):

Power Output:

• 300 watts RMS/channel; 20 Hz – 20 kHz; THD<0.1%; 8 Ohms; one channel driven

• 550 watts RMS/channel; 20 Hz – 20 kHz; THD<0.2%; 4 Ohms; one channel driven

• 300 watts RMS/channel; THD<0.1%; 8 Ohms; two channels driven

• 490 watts RMS/channel; THD<0.1%; 4 Ohms; two channels driven

• 200 watts RMS/channel; THD<0.1%; 8 Ohms; ALL SEVEN channels driven

Power Bandwidth (at rated power; 4 Ohm - 8 Ohm load): 20 Hz to 20 kHz (+ / – 0.1 dB)

Broad Band Frequency Response: 5 Hz to 80 kHz +0/-2 dB

THD + noise: < 0.005%; at 100 watts RMS; 1 kHz; 8 Ohms

Signal to Noise Ratio (8 Ohm load):

• > 117 dB; ref FTC rated power; unbalanced input (A-weighted)

• > 91 dB; ref 1 watt; unbalanced input (A-weighted)

Minimum Recommended Load Impedance (per channel): 4 Ohms (which equals one 4 Ohm load or two paralleled 8 Ohm loads)

Damping Factor (8 Ohm load): > 500

Input Sensitivity (for rated power; 8 Ohm load): 1.71 V

Gain: 29 dB

Note: The values shown refer to the amount

of power the amplifier would consume while playing test tones

continuously, on all channels, at full power, into a load bank.

Therefore they are not at all characteristic of what you would expect

when playing music or the sound track from a movie.

Normal audio

signals are dynamic, so the amount of power they require from second to

second varies widely, and the average is far lower than this. With

normal content, even playing very loudly, one of our amplifiers will

consume far less power than indicated in the chart, so these

values should not be considered to be a circuit requirement for normal

operation. 

Input Impedance: 

• 33 kOhms (balanced)

• 23.5 kOhms (unbalanced)

Input And Output Connections

•

Input Connections (High-Powered Single Channel Modules): Unbalanced

(RCA); balanced (XLR); one each per channel, independently selectable.

• Input Connections (Stereo Modules): 2 Unbalanced (RCA); 2 balanced (XLR); two per channel, independently selectable.

• Speaker Output Connections: Audiophile grade, gold plated, 5-way binding posts.

Trigger:

• Trigger Input: 5 – 12 V (AC or DC); <10 mA input current required

• Trigger Output: 12 VDC; can drive any load up to 120 mA

Power Requirements

Between 100 VAC and 250 VAC @ 50 / 60 Hz (automatically detected).

Front Panel Controls and Indicators

• Standby: push button (halo ring changes color to indicate Standby or On).

• Status LEDs: one per channel; blue.

• Status LEDs change to red to indicate a fault condition.

Rear Panel Controls

• AC Power switch: rocker switch (switches AC main power).

• Status LEDs switch: disables front panel Status LEDs and dims Standby button halo.

• Input selector switches (one per channel):  metal toggle switches; select between balanced an

Maximum Power Consumption: 2,600 watts.

320 watts/channel RMS into 4 Ohms; all channels driven

300 watts/channel RMS into 8 Ohms; two channels driven

490 watts/channel RMS into 4 Ohms; two channels driven